JOIN THE AUDAC STORY
Stay up-to-date with our new products, upcoming events and AUDAC projects worldwide
1
Operation indicator LED's
2
Class A/B amplifier technology
3
Advanced protection circuitry
4
24V emergency power input
5
Terminal block output connections (100V, 70V, 25V & 4Ohm)
6
XLR input & linktrough connections
7
Input gain control potentiometer
8
High pass filter switch
9
High pass filter switch
- Operation indicator LED's
- Class A/B amplifier technology
- Advanced protection circuitry
- 24V emergency power input
- Terminal block output connections (100V, 70V, 25V & 4Ohm)
- XLR input & linktrough connections
- Input gain control potentiometer
- High pass filter switch
- High pass filter switch
The CPA24 is a professional single channel 100V power amplifier with a power of 240 Watt, especially designed for most common 100V PA systems, and perfect to be used in combination with the CPR12 pre-amplifier. It is designed as a no-nonsense amplifier with only the necessary controls and connections. This creates great simplicity in use and installation. There are several power output taps available for use in 100V, 70V and even 4 Ohm Low impedance installations and they are fitted with an advanced multipurpose protection circuit. The protection circuit detects DC malfunction, short circuit, overheating, overload and limits the signal when necessary. Another present feature is the 24 V DC connection for powering the amplifier with emergency power when the main power is shut down. At the back of the amplifier, there are trim potentiometers to set the input level, a high pass filter switch and a ground lift switch provided. The input connection is made with balanced XLR connectors, and there’s a signal output for linking with other amplifiers. The steel 19" housing has a height of 2 HE.
| System specifications | ||||
|---|---|---|---|---|
| RMS Power | 240 W | |||
| Signal / Noise | > 90 dB | |||
| THD+N (@ 1 kHz) | < 1% | |||
| Technology | Class A/B | |||
| Protection | DC Short circuit | |||
| Over heating | ||||
| Over load | ||||
| Signal limiting | ||||
| Cooling | Dual speed controlled FAN | |||
| Operating temperature | 0° ~ 40° @ 95% Humidity | |||
| Frequency | Response (± 3 dB) | 70 Hz - 18 kHz | ||
| Power | Supply | Conventional (Transformer) | ||
| Source | 230 ~ 240 V AC / 50 ~ 60 Hz (110~115 V AC / 50~60 Hz after connection change) | |||
| Inputs | Sensitivity (1W/1m) | -12 dB ~ 0 dB | ||
| Impedance | 10 kΩ balanced | |||
| Connector | XLR female with Male Linkthrough | |||
| Outputs | Voltage / Impedance | 100 V / 42 Ω | ||
| 70 V / 21 Ω | ||||
| 31 V / 4 Ω | ||||
| Connector | 4-pin Euro Terminal block (Pitch - 7.62 mm with locking) | |||
| Product features | ||||
|---|---|---|---|---|
| Dimensions | 18.98 x 3.46 x 12.99 " (W x H x D) | |||
| Weight | 28.66 lb | |||
| Mounting | 19” | |||
| Unit height | 2 HE | |||
| Construction | Steel | |||
| Colours | Black | |||
| Accessories | Included | 4-pin Euro Terminal Block outputs connector | ||
| 2-pin Euro Terminal Block 24V Power connector | ||||
| Optional | CPE100 Rack mount handles | |||
Product
-
How is the power consumption of amplifiers tested & indicated?
As the power consumption of an amplifier, strongly depends on how hard the amplifier is driven, measurements are provided for various loads: idle, 1/8 of average full power, 1/3 of average full power, and full power.
Idle
Current draw at idle or with very low signal level1/8 Power: Pink Noise
Amplifiers are tested using pink noise signals to simulate real-world speech and music signals. It approximates operating with music or voice with light clipping and represents the amplifier's typical "clean" maximum level, without audible clipping. This 1/8 power signal provides a very good approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven as loud as possible without clipping the amplifier.1/3 Power: Pink Noise
1/3 Power Pink Noise is similar to 1/8 Power Pink Noise, except that it is a significantly more powerful input signal. It approximates operating with music or voice with very heavy clipping and a very compressed dynamic range. This 1/3 power signal provides an approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven loud enough to clip the amplifier heavily, and produce severe, audible distortion.Full Power
Current draw at full power is measured with a sine wave at its maximum possible level. However, it does not represent any real-world operating condition and represents the absolute extremes that an amplifier could ever experience.
Beautymania - Astana, Kazakhstan
Kazakhstan is one of the fastest growing economies in Central Asia and the birthplace of the idea for a new self-service store chain selling perfume a ...
Discover this project
Porsche Centre Antwerp - Wommelgem, Belgium
Ever since the foundation of the luxurious German car brand Porsche in 1931, their main principle was, and still is, to always get the most out of eve ...
Discover this project
St. Aldegondis Church - Zwevezele, Belgium
In the Belgian village of Zwevezele you will find a beautiful parish church, the St. Aldegondis Church.
Discover this projectInformation sheet English
Select additional information to show on your product sheet
Architect's and engineer's specificationsTechnical drawings
Shipping and ordering
Create product information sheet